Exterior Wood Rot Repair: Fix, Replace and Repaint Properly

Exterior wood rot is repaired in a fixed order. First you stop the water getting in. Then you cut out the decayed timber, consolidate or replace what remains, and finally seal the repair with a properly applied paint system. Skip the first step and the rot returns. Skip the last and the repair soaks up water within a few seasons. This guide takes you through each stage for window frames, sills, fascias, doors and cladding, and shows where the finish decides how long the repair lasts.
TL;DR
Wood rots because it stays wet. The Property Care Association says fungal decay arises when timber’s moisture content rises above 20%, so the damp source must be found and fixed first.
Probe suspect timber with a bradawl or penknife. Soft, crumbling or easily penetrated wood is decayed, whatever the paint looks like.
Small, localised rot can be cut out and repaired. Extensive rot, or rot in structural timber, means replacement and a professional assessment.
Suspected dry rot needs a timber decay specialist before anything is cut out or covered.
A repair is only as durable as its paint: rub down, prime and apply at least one undercoat and one finish coat.
Table of Contents
How to tell whether exterior wood is rotten
Paint that is flaking, bubbling or stained is a warning, not a diagnosis. The SPAB (Society for the Protection of Ancient Buildings) says a window should never be condemned on surface appearance alone. Breakdown of the paint is often linked to wet rot but not always. Equally, the Canadian Wood Council points out that wood can look normal and still have lost significant strength, so you need to test it.
The probe test
Push a bradawl, screwdriver or penknife into the vulnerable spots: the underside and ends of window sills, the bottom rail of casements, the base of door frames, the joints of fascias and bargeboards, and anywhere paint has cracked. The SPAB recommends probing with a sharp instrument and inspecting ideally once a year, or at least as often as you redecorate.
Sound timber resists the point. Decayed timber lets it in easily. The Canadian Wood Council describes a variation: lever up a thin splinter with a knife point. Sound wood lifts in long fibres, while rotten wood snaps and crumbles into short pieces.

What wet rot looks like
Wet rot is the common form on exposed joinery. According to the SPAB, some species leave timber bleached, softened and fibrous. Others darken it and crack it across the grain. You will usually see the timber feel soft or spongy, with paint lifting over it and sometimes a damp, musty smell.
What dry rot looks like, and why it matters
Dry rot, caused by the fungus Serpula lacrymans, is the most serious form according to the Property Care Association. It can spread through masonry and into other timbers, so it is not a job to treat with a tub of filler. If you see white cotton-wool growth, fine grey strands, an orange-brown dusty fruiting body or timber that has split into cube-shaped pieces, stop and have a timber decay specialist confirm what it is.
A note on moisture meters
A moisture meter helps, but it is not a verdict. A reading above roughly 18 to 20% points to timber wet enough to rot. The SPAB warns that surface readings from electrical meters can be misleading, so treat the meter as one clue alongside probing and a look at the surroundings.

Find the water before you touch the wood
The SPAB states that dry timber is immune to fungal attack, so the first measure in arresting decay is removing the cause of dampness and allowing the wood to dry below 20% moisture content. Typical culprits on a UK home are:
leaking or overflowing gutters and downpipes soaking fascias and window surrounds
failed or cracked sealant where frames meet the masonry
blocked drip grooves and sills with no run-off
paint that has cracked, letting water into end grain
ground levels, planters or decking piled against timber
condensation on glazing running onto the frame; the causes are covered in this guide to window condensation causes and fixes
If you replace rotten timber but leave the gutter dripping on it, you have simply bought the fungus a fresh meal. Fix the leak, clear the drip groove or reseal the joint, and give the area time to dry before repairing.
Repair or replace?
The honest answer depends on how much sound wood is left and what the timber does.
Situation | Usual approach |
Small patch of wet rot on a sill, rail or frame, surrounding timber firm | Cut out the decay and repair or splice in new timber |
Rot confined to one end or section of a joinery member | Splice in matching new timber |
Rot through most of the section, or timber that has lost its shape | Replace the component |
Easy-to-replace trim such as fascias, soffits or boards | Replacement is often simpler |
Load-bearing or structural timber | Professional or structural assessment before any work |
Any sign of dry rot | Specialist survey first |
The SPAB notes that commonly only a small area is affected, such as the bottom of a window with wet rot, and that a skilled carpenter can let in new timber rather than renew the whole frame. Its timber windows advice describes renewing a decayed bottom rail end or cutting back a rotten outer section of a cill. In the US, This Old House makes the same distinction: repair localised rot where enough good wood remains to support it, replace when damage is extensive.
The Canadian Wood Council adds a warning worth taking seriously: by the time decay is noticed, the wood has typically already lost substantial strength. If the timber carries weight, such as a lintel, beam or porch post, have it assessed by a structural engineer.
How to repair localised wet rot, step by step
This is the routine for a small area of wet rot on non-structural exterior timber. It follows the SPAB’s principles for wet rot and the manufacturer’s instructions for the repair products.
1. Cure the cause and let the wood dry
Fix the leak, gap or drip. Then allow time for the timber to dry out. Painting or filling damp wood traps the moisture and starts the cycle again.
2. Remove the decayed timber
Cut or scrape back to firm wood. The SPAB advises removing decayed timber only as far as necessary: take out what is soft and no more. For wet rot there is no need to cut a metre beyond the visible damage, and the SPAB describes routinely cutting back a 0.3 to 1.0 m margin as rarely justified. Dry rot is different, which is why it needs a specialist.
3. Harden what is left, or splice in new timber
For shallow decay, a wet rot hardener soaks into the remaining fibres and gives a solid base. For deeper damage, a proper timber repair is better. The SPAB’s repair principles for splices are:
remove the minimum of existing timber
do not mix timber species in a repair, because differing expansion will open the joint
match the grain line and density of new, well-seasoned timber to the old
shape the joint so that water runs to the outer face and does not sit on the joint line
fix mechanically with pegs, dowels or non-ferrous screws as well as glue
work the new material to the line of the existing, not the other way round
Replacement timber for a sill or similar should be a known durable species, and the Property Care Association says replacements should comply with BS 8417:2011 for preservative treatment, with any cut ends retreated.
4. Fill small losses with a two-part filler
Where decay is minor, a two-part wood filler used with the matching hardener builds the surface back up. For example, Everbuild’s data sheet says to remove as much rotten wood as possible, harden the remaining area, mix a golf-ball volume of filler with a 38 mm strip of hardener, press it in slightly proud and sand after about 30 minutes. Follow the instructions on whichever product you use, because setting times vary with temperature.
Filler is a patch for small areas. It does not replace structural timber and does not cure a damp source.
5. Sand, prime and paint
This is the step most repairs fail on, and the next section covers it.
Why the paint system decides how long the repair lasts
The SPAB is direct about it: a poor or badly maintained paint finish lets water into the timber, causing swelling and a continuing cycle of decay. Its guidance is to rub down accessible surfaces, prime any exposed timber and apply a minimum of one undercoat and one finish coat. Paint choice matters too. Alkyd systems are the most common on external joinery, with metal-based primers for hardwoods and linseed oil paint as an alternative.
The same note stresses that preservatives have a limited life and are no substitute for good detailing and regular maintenance. In practice that means:
Seal the end grain. Cut ends and joints are where water enters first, so they need priming and a full coat.
Paint into the joints. Bring the paint slightly onto the glass or the adjoining surface so water cannot track under the film.
Don’t paint over damp timber. Wait for dryness, or the coating blisters.
Recoat before it fails. Repainting on a regular cycle is far cheaper than repairing rot. Our piece on why regular maintenance painting protects your home explains the logic, and what weatherproof painting involves covers coatings built for exposed surfaces.
Flaking sills are often the first visible sign of trouble, and our guide to flaky window sills shows how to read the paint failure and repaint so that it lasts.
Other ways to keep rot from coming back
Keep gutters clear and repair any cracked sealant or mastic around doors and windows.
Isolate timber from damp masonry, for example with steel joist hangers or damp-proof material, as the Property Care Association recommends.
Use timber suitable for ground contact for fence posts and decking, and clear standing water from decking.
Improve ventilation where condensation collects.
Inspect each year, ideally before you repaint, using the probe test above.
For uPVC windows and doors there is no rot to treat at all, but faded or tired frames can be sprayed instead of replaced: see our UPVC spraying service.
When to call a specialist before you repair
Some rot is beyond a weekend repair, and acting early protects your home:
Suspected dry rot. The Property Care Association says wood preservatives should not be relied on for long-term protection against dry rot where timbers stay wet, so identification and a treatment plan come first.
Structural timber. Roof members, lintels, porch posts and balcony supports need a structural assessment.
Unclear damage. Holes, frass (fine powdery dust) or flight holes may mean wood-boring insects rather than fungus. This wood-boring pest identification guide helps you tell them apart before you decide what to do.
Widespread decay. If probing finds soft timber in many places, the cause is probably larger than a single leak.
Landlords and property managers should also record the survey and repair so the condition of the building is documented.
Our view on rot, repairs and repainting
We are painters and decorators, so we see the end of the story more often than the start. A sill is repaired, the filler is sanded flush, and then everything depends on what goes over it. A repair finished with one thin coat of whatever was left in the tin will be taking in water again within a couple of winters. That is why we treat the paintwork as part of the repair, not an afterthought. Proper preparation, the right primer, and enough coats on the end grain and joints are what keep water out. On exterior work we also use airless spraying, which lays down an even coat across large areas such as cladding, fascias and render, and our UPVC spraying restores window frames and doors that look tired without replacing them. We are a family business, run by brothers Gus and Rhys, covering Cornwall and the South West, where wind-driven rain and salt air test exterior timber hard. Our advice is always the same: deal with the damp first, repair only what needs repairing, and make sure the finish is built to last. Restoring an exterior properly, not just covering it up, is the heart of what we do. Angus
Getting the finishing done properly
Once the timber is sound and dry, the finish is where our work begins. We paint and restore exteriors for homeowners, landlords and commercial property owners across Cornwall and the South West, from exterior home painting to exterior home cleaning before a repaint. If you are weighing up what a full job involves, our guide to exterior restoration is a good starting point. To discuss your property, get in touch through A Brush With Gus.

We do not publish set prices because every home is different, so the easiest route is to ask us for a quotation.
FAQ
Is there a way to fix rotten wood?
Yes, when the rot is localised and the rest of the timber is firm. Fix the damp source, cut out the soft wood, harden or splice in new timber, then prime and paint. Extensive rot or any structural timber needs replacement or a professional assessment.
Does wood hardener really work?
A hardener soaks into the fibres that remain and gives a firmer base for a filler, which is how manufacturers such as Everbuild describe it in their data sheet. It is meant for shallow wet rot after the soft material has been removed and the wood is dry. It is not meant to rebuild timber that has lost its shape or carries load.
How do I know if it is wet rot or dry rot?
Wet rot usually leaves timber dark or bleached, soft and cracked, in places that stay damp such as sills and door bases. Dry rot can show white cotton-wool growth, an orange-brown fruiting body and cube-shaped cracking, and it spreads. If you suspect dry rot, ask a timber decay specialist to confirm before you cut or paint anything.
Can I just paint over rotten wood?
No. Paint will not stop decay and the film will fail quickly over soft timber. Remove the decayed wood, repair it, let it dry fully and then apply primer, an undercoat and a finish coat.
How often should I check exterior timber?
The SPAB recommends inspecting ideally once a year, or at least whenever you redecorate. Probe the sills, bottom rails, door bases and fascia joints, and repaint before the paint film breaks down.
Sources
Recommended

Comments